At first developed to mimic a classic look (as identified on very old violins and mandolins) Sunburst is a classic guitar color frequently encountered upon guitars aged and newer. It's a highly desirable guitar finish but it it possible for the average person? It is possible to obtain a sunburst finish on your own guitar if you decide to follow a couple of basic steps and take your time and don't rush. It's wise for you to experiment first using a scrap part of lumber prior to moving on to the guitar.
If it is a totally new guitar kit,then you should assemble the guitar initially. Keep in mind you're going to be deconstructing to commence the finish but you should know you will not befinding problems with the guitar components that jeopardize the finish you've specifically put such a lot of valuable time towards. Once you've assembled the electric guitar and tested for potential issues you can begin to prepare the timber. Sand right back until you have an entirely smooth exterior to apply your finish. Finally remove unwanted dust and tidy the guitar diligently.
Following that administer plenty of wood grain filler. You'll want to coat thickly on the top of your electric guitar and afterwards really work it in. The moment it has dried remove the excess and remove any excess filler with a moist rag. It's now the time to apply paint to the back and sides of the electric guitar. A critical factor to keep in mind should be to mask the top and neck area. When you are spraying paint or lacquer it's a smart idea to keep the spray cans in warm to hot water before you start using. It is going to require a range of coats so you shouldn't attempt to apply too much simultaneously. The trick is to create the tint layer after layer and spray from a fair distance from the guitar in order to attain a gentle edge. The closer you end up getting the harder the edge line you will make.
Following that administer the amber lacquer. Chances are you'll be obliged to mask the sides of your guitar after which you can position the guitar on a firm workbench faced upwards before applying. Upon having finished this task you should administer the clear coat after that and use your sandpaper in between coats to get rid of any issues. After that apply the next pitch-dark stain to achieve a blend of colour between the edge and inner colors. Attempt to apply exceptionally thin and amass the required coats. At this time be certain to let the lacquer dry. The moment the guitar is completely moistureless focus on sanding for a second time.
This is the very last part. The trick here is to make use of a more lightweight gauge of sand paper every time as you get in a nutshell taking out the marks because of the gauge of sandpaper used beforehand soon after which progressing which has a lighter gauge. Continue to keep delicately sanding after that migrating to a lighter gauge if you do not run out of sandpaper after which you can move on to your buffer.About now you can basically continue to keep buffing or hand polishing until you end up getting completely fine with the finished look.
If it is a totally new guitar kit,then you should assemble the guitar initially. Keep in mind you're going to be deconstructing to commence the finish but you should know you will not befinding problems with the guitar components that jeopardize the finish you've specifically put such a lot of valuable time towards. Once you've assembled the electric guitar and tested for potential issues you can begin to prepare the timber. Sand right back until you have an entirely smooth exterior to apply your finish. Finally remove unwanted dust and tidy the guitar diligently.
Following that administer plenty of wood grain filler. You'll want to coat thickly on the top of your electric guitar and afterwards really work it in. The moment it has dried remove the excess and remove any excess filler with a moist rag. It's now the time to apply paint to the back and sides of the electric guitar. A critical factor to keep in mind should be to mask the top and neck area. When you are spraying paint or lacquer it's a smart idea to keep the spray cans in warm to hot water before you start using. It is going to require a range of coats so you shouldn't attempt to apply too much simultaneously. The trick is to create the tint layer after layer and spray from a fair distance from the guitar in order to attain a gentle edge. The closer you end up getting the harder the edge line you will make.
Following that administer the amber lacquer. Chances are you'll be obliged to mask the sides of your guitar after which you can position the guitar on a firm workbench faced upwards before applying. Upon having finished this task you should administer the clear coat after that and use your sandpaper in between coats to get rid of any issues. After that apply the next pitch-dark stain to achieve a blend of colour between the edge and inner colors. Attempt to apply exceptionally thin and amass the required coats. At this time be certain to let the lacquer dry. The moment the guitar is completely moistureless focus on sanding for a second time.
This is the very last part. The trick here is to make use of a more lightweight gauge of sand paper every time as you get in a nutshell taking out the marks because of the gauge of sandpaper used beforehand soon after which progressing which has a lighter gauge. Continue to keep delicately sanding after that migrating to a lighter gauge if you do not run out of sandpaper after which you can move on to your buffer.About now you can basically continue to keep buffing or hand polishing until you end up getting completely fine with the finished look.
About the Author:
Before you purchase a guitar kir anywhere else, check our website at www.eguitarkits.com for information related to Guitar Kits and general tips on finishing.
No comments:
Post a Comment